Homemade floetrol

This has happened to me many times. These paints already have low pigmentation, either the pigments are inferior, or it has been watered down already, and disaster awaits when you add more water when mixing your colours at home. This will give you less than stellar results, which could lead to disallusionment and finally giving up out of frustration. Also, flow enhancers help keep paints workable longer, this is a good thing for when you want your colours to blend as it gives the paint time to feather two colours together to make a third, for example.

But it increases overall drying time. Flow extenders can also be used to add to the shelf-life of your paints. Add a few drops to drying or thickened paint pots and shake it up to help restore them. A few drops occassionally to those rarely used colours help keep the paints ready to use.

But now, with Zinsser latex paint extender on the scene, this changes everything! My local Home Depot had it, they did not have Floetrol.

And the cost was much less than you know who? And it ships from the states, will there be a customs fee? I have used varathane and the results were very good. I tried Armorall, also the results were very good.

I mostly use white glue mixed with water 2 part glue, 1 part water and the results are very good, not one of the pouring mediums however provided any differences in the dried painting, so I used to use glue for the cost aspect. But now, I am a Zinsser gyrl! So be sure to experiment with whatever extender or flow enhancer you want. So test small amounts to see if you like the results.

Keep it fun and experimental, because as long as you experiment, you cannot fail, they are all lessons. And every lesson that you learn leads you to creating better art!

Floetrol vs Water - SURPRISING RESULTS!

However, it was not easy to find. Like Like. Like Liked by 1 person. What proportions would you recommend for using Zinsser with cheap craft paint such as Americana…. I have not tried an acrylic pour yet…have been doing research.

Thank you. I will be using Zinsser only as my pouring medium.

Suppose that four equal positive charges are located at the corners

Water just breaks the paint. Edited July 13 — The pours I did yesterday were very lovely this morning. The colours were defined and no cracking! My recipe as of today is; mix acrylic paint with white gluehalf and half, then add zinsser to thin it to pouring consistency. I do not dilute the zinsser or glue anymore.

Be careful, read the material safety data sheet MSDS for every product you decide to experiment with. I saw some artists using a polymer medium developed for a different pupose, lots of nasties that made me move on after I read the MSDS. I would also put a disclaimer on your blogs if you are not a subject matter expert when you recommend chemicals to the people following your blog. Make sure you are familiar with the effect of these chemicals after prolonged exposure to them.

Hi Debra, You must have missed the part where I mentioned that Zinsser is a latex paint extender like Floetrol. Like Liked by 3 people. I have done two seperate pours, one using paint and zinsser no dilution and one mixing white glue with the paint and than using zinsser no dilution to thin it further and both have given me similar results. So I will continue to mix glue and paint and then adding zinsser to condition the paint, so to speak.Next post: Paint Pouring with the Leftovers.

If you can pour paint out of a cup and can tilt a canvas, then you have all the necessary skills to make a colorful piece of art to hang on your wall with paint pouring. At the end of this post, there is a supply list along with reminder notes for your reference.

Greenridge farms beef sticks costco

Drips happen with paint pouring so you need something to catch the drips. My favorite is a cardboard box with a cooling rack from the kitchen section. Level your canvas as best you can. I am clearly not an engineer, so about level is the best I can do. Is there one perfect pouring medium? There are many to choose from and they each have their pros and cons.

What I found was that if I had a tube, just over 2 oz. When I used Liquitex soft body paint, I used less paint, about a third of a 2 ounce tube. As long as it looked like the color in the tube, I would be good. So when I mix the paint, if it looks lighter than what comes out of the tube, I add more until it matches. Air bubbles are the enemy of paint pouring. To make a dirty pour, you layer color in a cup. The more layers you have, the more intricate the pour.

The silicone helps make cells. I only added it into the white. Making dirty pour layers is a breeze with the paint in those condiment squeeze bottles. Then add the rainbow from the cup. You might have seen that winding road with very tight curves.

Woman killing chicken iran

Once the paint is on the canvas you have a choice. To leave it just the way it is or to mess with it. I chose to mess with it by tipping it and letting gravity pull and stretch the color. Once you have it how you like it, then let it drip for minutes on the rack, then the move it to a homemade drying rack. It will stick.

Abcd ka khoj kisne kiya tha

Trust me, it will really stick. How do I know? I did it once and had to almost pry it off with a crowbar. So I built a drying rack for the next one.

Just 4 cups hot glued to cardboard in the width of the canvas. This allows the edges to not touch a thing as they dry and it frees up the main pouring rack and box so you can keep on making more poured canvases while this dries.Post a Comment. Posts on this website may contain affiliate links. For more information, please read my disclosure policy.

Thank you for your support of this website and our family. Floetrol is a pretty cool product. It is a paint conditioner, normally used with a sprayer, or if you want a really smooth finish. I rarely use it for that, though. Instead, I like to use Floetrol to create my own custom glazes.

For example, I used my Floetrol glaze to transform this table. But the bright white legs were just too harsh against that espresso top, so I began by distressing the white paint with my sander. Then, I mixed some dark brown paint with Floetrol and rubbed it on slathered it all over like cream cheese on a bagel. Working with one section at a time, I continued to slather it on and then wipe off the excess. If you want it thinner or lighter, use less paint and more Floetrol. Here, I used 2 parts Floetrol to 1 part paint.

The finished project! You can see that my custom glaze added a subtle depth to the finish, darkening both the white paint and the raw wood beneath. The table is no longer for sale, however.

What color glaze would you make? Deep turquoise on a light aqua painted piece? Pewter on a lighter gray paint?

homemade floetrol

Or maybe just white and brown like I did? Thank you for supporting On the Banks of Squaw Creek. To follow along with 31 Days of Decorating with Junk, enter your email address top right or become a fan on Facebook. See you tomorrow! Sign up for my monthly email newsletter, with new posts, old posts, recipes and more! No comments:. Newer Post Older Post Home.A huge thank you to Stephanie of Deliberately Creative for testing out all of these alternative mediums for the acrylic pouring community as large!

Check out how they perform in this fun comparison experiment. There are 2 videos to watch. There are a lot of different options for medium alternativesome are more household some are a little bit more artsy, but everything in this video is a quality cheaper alternative. All of the paints in this video are mixed with four ounces of pouring medium and pigment powders.

Pouring four ounces makes it easier to divvy up the paints evenly into the smaller cups for the experiment. Starting with the Behr Premium Plus, mix everything very thoroughly to make sure that the half a teaspoon powders are fully incorporating into the medium. Make sure the paint is smooth with no color chunks before you call it a day on the mixing. The Behr pours best after being freshly stirred. Using your color less medium cup, begin spooning medium onto your canvas, coating the canvas completely.

Next, begin pouring your pigments, in this video stripes are being poured going from the bottom right of the canvas up to the right with the tongue depressors to keep everything smooth and even. Keep your colors in their own rows so you can see more results when you begin to tilt. When color is distributed to your liking, begin tipping and tilting your canvas to get the paint moving.

Try to avoid over mixing! In the video, because of its thickness, a straw was used to help spread the color after tilting was completed.

The Golden polymer also moves slowly as tilting begins and colors stay more distinct without much blending from just tilting. When air manipulation is introducedthere is plenty of movement and a lovely cloudy quality to the metallics over the medium.

You will need to stir each of these pigmented paint cups before pouring to make sure that it has the proper amount of movement.

Acrylic Pouring With Floetrol

While tipping, the Behr glaze has the most movement, despite how thick it is, but the colors also remain completely separate, even after using the straw. The Behr medium dried with a matte finish that lets the Pearl Ex pigments metallic shine through but with a cloudy finish rather than a clear one. Finally, the Golden finished with an exceptional glossy finish, though the pigments created some texture and there was some bubbling that created tiny holes.

From the findings of this video, Golden was declared the winner of this alternative medium mixing experiment! Give the winner or the runners up a shot during your next pour! As in part one, the medium will be divided into four cups; three with color and one without.

For the pigment cups, you will again use about half a teaspoon of your Pearl Ex powder. Something we learned from part one is that letting the pigment powder and medium sit together for about five minutes helps the color and consistency. Mod Podge needs twice as much effort to get the pigment powder incorporated but there still happened to be specks of powder left over, Golden GAC had a similar mixing problem but allowing it to sit a while longer could be a solution.

The Liquitex Gloss and Varnish created the richest color and the most metallic finish compared to the Liquitex pouring mediumbut it does have the thickest consistency and required water to cut it down. The thickness also made bubbles an issue during mixing because of the folding. After four milliliters of water was added, everything was stirring like clockwork! Tilt, tilt, tilt, and then grab your straw.Floetrol is a paint conditioner that can be used with water based paints like flat or semi-gloss latex, enamel paints, Acrylic, or Vinyls.

Floetrol helps these water based paints perform more like oil based paints which ultimately makes using the paints easier as latex paints can tend to be heavier making them less forgiving when being sprayed as well as having a greater likelihood of leaving a brush or roller mark behind when being applied by a brush or roller.

Floetrol will reduce brush marks in your paint finish and make spraying your paint easier. Floetrol can help make water based paints easier to work with when environmental conditions are not forgiving. Environmental conditions that typically can create problems for water based paints like temperatures that are too hot or humidity is to low causing paints to dry to fast. Floetrol can sometimes help reduce water based coatings performance problems when high temperature is causing your waterborne paint to dry to fast or your concerned about your paint drying to fast as floetrol will extend the dry time of the paint.

Since Floetrol causes paint to flow with greater ease you have to be a bit more precise when applying as it can create runs. This is not always a problem but just requires a bit of pre-planning before using Floetrol. You also want to try floetrol with your individual paints to ensure there are no undesired results with your paint like gritty finishes or color changes to your coating.

Additionally, if you add to much floetrol to your paint you could reduce the coverage of the paint which means you will have to apply more to cover the product you are painting. Floetrol is mixed into your water based paint thoroughly and then you apply the water based paint either by brush, HVLP spray gun, or airless paint sprayer depending on your application. For a brush and roll application you can mix up to 8 ounces of floetrol per gallon. Start with 8 ounces in all applications and gradually increase the amount as needed.

Monitor your paint and if it seems to be flowing well you can stop adding additional floetrol. If your using floetrol there are limitations to when you should consider Floetrol. If your paint is a high gloss paint you will want to consider mixing the Floetrol with water as floetrol can reduce the gloss of your coating if too much is mixed directly with the coating.

Never use floetrol with oil based paints rather use a paint conditioner specifically formulated for water based paints. Floetrol provides additional benefits over just water. Water will only reduce or thin the paint you are using. Floetrol is a conditioner which means it enhances the qualities of the water based paint your using while also helping it to be thinner for easier application. By not just thinning the paint you will achieve better performance out of your paint when it is applied.

Floetrol can help make spraying latex paint easier. If your having trouble spraying latex Floetrol will make the paint thinner which helps with achieving better looking finishes when spraying as well as reducing issues with airless tip clogs.I have really enjoyed using Floetrol as a pouring medium. It seems to do a pretty good job and stands up well under resin. One thing I have noticed is that floetrol over older paint is not as forgiving.

The recipe was pretty simple. I used 1 ounce of floetrol to about 20 drops of fluid acrylic. Below is a list of the items we used in the demonstration. This weekend I tried something a little different with my test canvases. I did a dirty pour with three flip cups, and I think it turned out OK. Below is a video from my YouTube channel with all the details. Additionally, I coated the piece in Art Resin. Eventually, the piece will be available on my Etsy Page that I was finally able to setup.

I am busy with so much other that stuff it seems like I am moving in slow motion. The Etsy shop is pretty much where these little test pieces reside. Otherwise, they collect dust in my house. So check it out and buy something will ya! As always here is a list of the ingredients I used to create this piece. I hope this inspires you to try it out. Teaching my 8 year old to paint using acrylic pouring medium and mixing colors is probably one of the most fun things I do each week.

Rc snowcat amazon

She just loves to make the magic happen and I love to watch her learn new things. This week we did a little 8 inch canvas using some metallic paints and jewel tones. We like the results and decided to spray a little silicone on the painting at the end of the pour. Cells were created instantly! However, after the painted dried they were not as interesting as the ones that appeared naturally.

For the painting in the video and seen above we made a list of the materials used in case you wanted to try some of this out. This Sunday afternoon my youngest and I made a little artwork.Floetrol mixed with paint makes a huge difference when painting cabinets, doors, trim or furniture pieces. Floetrol is a liquid paint conditioner that you just pour into your paint and it greatly helps to reduce paint build up on brushes, extends the drying time, helps to create a smooth finish and it virtually eliminates brush marks.

I was first introduced to Floetrol more than 7 years ago when I had my kitchen cabinets professionally painted. My painter told me not too worry because he had a secret weapon; Floetrol. I was blown away by how gorgeous and sleek my cabinet finish looked after he painted it with the Floetrol mixed with paint:. There are no brush marks to be found and the paint finish is so uniform, sleek and smooth. Keep in mind that these cabinets were painted more than 7 years ago and it was the third time they were painted and they still look like new.

My cabinet paint finish has also held up amazingly well and today 7 years later, they look like they were just painted. I have used Floetrol to paint my bathroom cabinets, doors, trim and on several of the furniture pieces that I have painted and the finish is always so beautiful!

The color is a Sherwin Williams custom mix that I tweaked using four different colors. Over the last year, mixing my own chalk paint has become an obsession for me. I started mixing lightweight spackle with paint for my faux plaster finishes. The spackle mix gives me the most gorgeous chalky finish and I only have to use one coat. The chalky magic happens after the mix is brushed on and completely dries. The color becomes so elegantly rich and the finish is simply gorgeous. My recipe for the chalk paint using lightweight spackle is equal parts of spackle, flat paint in your desired color, and latex primer.

Paint Pouring For the First Time

For larger furniture projects, I mix two cups of each. If you want more of a plaster look that is thicker, you can increase your spackle. I have tried every painters tape on the market over the years.

homemade floetrol

Up until recently, I used Scotch Blue tape but I recently started having paint seep under the tape. Works like a charm every time! PaintBlock is a super-absorbent polymer which reacts with latex paint and instantly gels to form a micro-barrier that seals the edges of the tape, preventing paint bleed.

In other words, music to our ears! Paint will not seep! Be sure and get the right FrogTape for the right surface and you can find this amazing tape at both Home Depot and Lowes. The wrong rollers for the job can splatter or leave uneven patches of paint.

From my experience, it makes a big difference to spend a tad bit more money for a specific brush, like a latex brush with bristles that are designed for latex paint. They could be grabbing a brush specifically designed for applying wood stain and not realize that its the worst possible brush to use for something like a latex project. The same thing applies to paint rollers.

People may not realize that they may be buying a roller designed for ceilings, which is not ideal for rolling paint on walls. Help with Choosing the Right Paint Color. If you missed it a few weeks ago, I shared some favorite tips and tricks for choosing a paint color.

You can get to that post by clicking the image below:.

homemade floetrol

Need a little more help in trying to figure out how to pick a paint color? You can see my explanation of the paint elimination process that I go through in this segment that I did for Fox 26 Houston Weekend Morning News. You can go to the video by clicking the image below:. I am about to sand by 2 year old cabinets and paint them a cream white.

Right now I am very nervous to not get the DIY look but a professional look.


thoughts on “Homemade floetrol

Leave a Reply

Your email address will not be published. Required fields are marked *